One Landscape Light Not Working
Hedge trimming trenching or nearby construction are most often the culprits. Most of the outdoor solar garden lights come with ONOFF button and that button needs to be turned ON.
In many cases this simple thing is ignored by many people and this is one of the main reasons why your solar light isnt working as expected.
One landscape light not working. Cut cable or short. Check to make sure the toggle switch is in the correct position or see if your fuse stat is blown. There should be a toggle switch or a fuse stat inside the transformer.
Once youve checked the entire system you can turn the circuit breaker back on to verify that the lights work properly. Lamps are burning out prematurely. If some of your landscape lights arent working there are a few options you can try.
There Is ONOFF Button Its not turned ON. Placing photocells or timers on the transformer will make the lights go on and off at regular intervals. There are so many possibilities that can cause your lighting system to not operate as it should such as circuit breaker has tripped cut line in the beds from pruning or planting bad lamps bad connections lightning etc.
Many do-it-yourself landscape lighting kits use wire piercing connections because they are quick and easy to install. If a new bulb doesnt work turn off the switch or pull the plug turn off the power that is and try bending up the little metal tab inside the bulb socket. Well lets dive into some of the most common reasons why your landscape lights are not working.
If they are run at a higher voltage they burn out faster. Look to see if the light fits properly in the socket. Use a voltage tester and check for power on the landscape wire.
Proper voltage at the light Low voltage lights should fall between 108 and 12 volts. These can get pressed in so far that they no longer touch the bulbs electrical contact. If you do have power at your transformer and the lights still arent turning on there is likely a short causing the transformer to shut off.
To repair your low-voltage landscaping lighting you may need a Phillips screwdriver a digital voltage meter wire nut connectors a small shovel and pliers. In this case you can replace the bulb with a new LED bulb with a suitable socket. The first place we see corrosion is in the socket where the lamp is installed.
One cable run not working. Here we explain illustrate how to inspect and test a dawn-to-dusk floodlight or security light that is not working. Sometimes the light can malfunction and not turn on when it is supposed to.
For incandescent bulbs look for breaks in the wire filament the wires inside the glass part. Common problems include pinched wires near the fixture or loose bulbs. If your voltage is above 12 you will be replacing the bulbs often.
As a result your landscape lights stop working and replacement bulbs will fail to light. Southern Lights offers the essentials when it comes to lighting. Usually a burning lamp will produce enough heat to burn off any condensation moisture that may form in a light fixture.
If the lamp burns out corrosion can form in that light socket. Repair the damaged wire and clear the fault. If power is not detected on the landscape wire.
Test the light fixture. This article describes diagnosing fixing an outdoor light that is not working. You should first check whether the fuse for this circuit has tripped.
Starting with how to use a neon tester to confirm that electrical power is off before touching electrical wires we continue with a list of things to check if your outdoor light wont turn on. This could be caused by power problems a broken sensor or faulty bulbs. If it isnt it may need replacing.
Design I Install I Repair. Excessive voltage at lamp. Experience Certification and Passion set us apart.
If they run at a lower voltage they are dimmer and tend to go black because the Halogen Cycle does not work well and tungsten is deposited on the bulb glass. Test cable for voltage if none then it is cut if there is very low voltage and the cable is hot then there is a short. If your light has a voltage of less than 108 volts the light will be too dim.
The downside is that as the copper corrodes the connection loosens over time. Reset the circuit breaker. Your Halogen light bulbs in your low voltage system run best from about 108 volts to 118 volts.
If the circuit is tripped locate the problem within the circuit wiring. If a section of your landscape lighting system suddenly goes out it is possible that a line was cut. Southern Lights Landscape Lighting is also an Award Winning Lighting Design Install firm offering clients a full range of lighting and outdoor audio services.
12 - 15 volts DC is typical and what to look for. Check the socket to see if it is giving power. Open the transformer for access to where the landscape wire is attached to the transformer output terminals.
Locate the circuit breaker which provides power to the light switch and make sure it is not tripped. It can also happen that a newly installed LED ceiling light does not work. We can troubleshoot these issues for you and most often all that is needed is a splice to connect the wire.
If the ceiling light has already worked before the lamp may be broken. Then you should check whether the light sources are replaceable. This takes a lot of time but it happens often.
Fixing this malfunction is usually a quick and simple process. Check all fixtures and splices for defects. DIY kits may be to blame as well.
